 
Aerospace Protectant (Return to Product List)
Prior to Treatment:
If surface is stained, dirty or discolored, clean the area with the proper cleaner to prep the surface for protection. We suggest 303 Fabric Cleaner or 303 Cleaner & Spot Remover. As with any new product, test in a non-visible area to ensure desired results are achieved.
Products Recommended:
303 Aerospace Protectant
Microfiber Towel(s)
Steps Taken:
1. Lightly mist Microfiber towel with 303 Aerospace Protectant
2. Work the Microfiber towel into the surface
3. Repeat steps 1 & 2 until entire surface has been covered with 303 Aerospace Protectant
For a matte finish, use a separate Microfiber towel and buff completely dry
For a semi-gloss, do not buff dry
Maintenance Schedule:
For ideal protection, we suggest protecting your rubber, vinyl and trim, at least once every 1-3 months.
Convertible Top Cleaner (Return to Product List)
Prior to Treatment:
Prior to deep cleaning your convertible top, you want to make sure it has been washed and dried thoroughly. This will remove light surface contamination, leaving the deeper stains for the 303 Convertible Top Cleaner.
Products Recommended:
303 Convertible Top Cleaner
Upholstery Brush
Microfiber Towel
Steps Taken:
1. Protect your glass and paint by taping off the exposed surfaces with painters’ tape and newspaper
2. Once just your convertible top is exposed, mist on the convertible top cleaner in the dirty areas
3. Use the Upholstery Brush on the stained area to help loosen debris embedded in the convertible top
4. Blot dry using a Microfiber towel
After Treatment:
After your convertible top is completely cleaned, make sure you protect your convertible top with the proper convertible top proofer. This will help your convertible top looking cleaner longer, help prevent damage from rain, snow, fading and road contamination. It will also help increase your resale value when you are ready to sell the vehicle.
Maintenance Schedule:
Pending on weather conditions, storage, sun exposure, amount of usage and other determining factors, we suggest cleaning your convertible with 303 Convertible Top Cleaner at least 2 times a year.
High Tech Fabric Guard (Return to Product List)
Prior to Use:
To prep the surface for using 303 Fabric Guard, we suggest following the procedure with 303 Fabric Cleaner. This will remove stains and contamination and bring the surface to a like new condition. Make sure surface is dry prior to using 303 Fabric Guard.
Products Recommended:
303 High Tech Fabric Guard
Steps Taken:
1. Lightly mist 303 High Tech Fabric Guard on surface
2. Allow up to 4 hours to completely dry for maximum protection
Maintenance Schedule:
We suggest reapplying 303 High Tech Fabric Guard every other month for maximum results.
Cleaner & Spot Remover (Return to Product List)
Prior to Use:
Before attacking a stain on your carpets or upholstery, make sure you brush the surface with a firm bristle brush to loosen any debris and bring it to the surface. Then vacuum as much of it up as you can prior to using 303 Cleaner & Spot Remover. This will help prep the surface for maximum cleaning results.
Products Recommended:
303 Cleaner & Spot Remover
Upholstery Brush
Steps Taken:
1. Spray 303 Fabric Cleaner onto the soiled area (on tougher stains allow 5-15 minutes to penetrate surface)
2. Agitate the surface with the upholstery brush to get maximum results
3. Vacuum up surface to remove loosened debris
4. Repeat as needed
After Treatment:
After cleaning with 303 Cleaner & Spot Remover, we suggest protecting your carpets and upholstery with 303 Fabric Guard. This will help prevent stains from settling into the carpets and upholstery and increase your resale value on your vehicle.
Maintenance Schedule:
As needed.
Fabric Cleaner (Return to Product List)
Prior to Use:
Before attacking a stain on your carpets or upholstery, make sure you brush the surface with a firm bristle brush to loosen any debris and bring it to the surface. Then vacuum as much of it up as you can prior to using 303 Fabric Cleaner. This will help prep the surface for maximum cleaning results.
Products Recommended:
303 Fabric Cleaner
Upholstery Brush
2nd Spray Bottle Optional
Steps Taken:
1. Dilute 303 Fabric Cleaner to proper strength, for everyday stains we suggest using a 10:1 (water: concentrate) mixture, check bottle for other dilution ratios
2. Spray 303 Fabric Cleaner onto the soiled area (on tougher stains allow 5-15 minutes to penetrate surface)
3. Agitate the surface with the upholstery brush to get maximum results
4. Vacuum up surface to remove loosened debris
5. Repeat as needed
After Treatment:
After cleaning with 303 Fabric Cleaner, we suggest protecting your carpets and upholstery with 303 Fabric Guard. This will help prevent stains from settling into the carpets and upholstery and increase your resale value on your vehicle.
Maintenance Schedule:
As needed.
Wiper Treatment (Return to Product List)
Products Recommended:
303 Wiper Treatment
Steps Taken:
1. Open up the wiper packet
2. Wipe off blade
3. Fold over to a new side of the wipe
4. Wipe off second blade
5. Repeat as needed
Maintenance Schedule:
Refill as needed.
Instant Washer Fluid Tabs (Return to Product List)
Products Recommended:
303 Instant Windshield Washer Tab
Water – We suggest getting a 1-gallon bottle of Poland Springs bottled water, etc.
Steps Taken:
1. Open up the bottled water
2. Drop tablet inside the water
3. Allow 30-60 minutes to fully dissolve
4. If still clumpy, give the bottle a quick shake
5. Pour mixture into your windshield washer fluid reservoir
Maintenance Schedule:
Refill as needed.
Aerospace Cleaner (Return to Product List)
Prior to Use:
Before attacking a stain on your carpets or upholstery, make sure you brush the surface with a firm bristle brush to loosen any debris and bring it to the surface. Then vacuum as much of it up as you can prior to using 303 Fabric Cleaner. This will help prep the surface for maximum cleaning results.
Products Recommended:
303 Fabric Cleaner
Upholstery Brush
2nd Spray Bottle Optional
Steps Taken:
1. Dilute 303 Fabric Cleaner to proper strength, for everyday stains we suggest using a 10:1 (water: concentrate) mixture, check bottle for other dilution ratios
2. Spray 303 Fabric Cleaner onto the soiled area (on tougher stains allow 5-15 minutes to penetrate surface)
3. Agitate the surface with the upholstery brush to get maximum results
4. Vacuum up surface to remove loosened debris
5. Repeat as needed
After Treatment:
After cleaning with 303 Fabric Cleaner, we suggest protecting your carpets and upholstery with 303 Fabric Guard. This will help prevent stains from settling into the carpets and upholstery and increase your resale value on your vehicle.
Maintenance Schedule:
As needed.
Fine Grade Clay Bar (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to using any type of clay bar. This will help remove major surface contamination and prep the paint for using the clay bar.
Products Recommended:
ClearKote Clay Bar
Quick Detail Spray
Microfiber Towel
Steps Taken:
1. Cut down the 200 gram into manageable sizes, we suggest using 50 gram pieces or ¼ of your full bar
2. Store remaining ¾ in the protective case along with a few sprays of the quick detailer to keep product moist
3. Kneed the 50 gram piece in your hand eventually working it into a flattened surface
4. Once your piece of clay is ready, directly mist your quick detailer onto the paint to lubricate the surface. Try to work in 2’ x 2’ sections
5. Using light pressure, glide the clay on the surface that you just lubricated. You should feel the dirt and grime being absorbed by the clay
6. When the 2’ x 2’ section is gliding effortlessly, then that area is complete
7. Remove excess quick detailer with a Microfiber Towel
8. As you move onto the next area, keep reshaping the clay in the palm of your hand so you get a fresh surface of clay
9. Repeat steps 3 – 8 until entire vehicle has been clayed
Total Number of Coats Suggested:
You should only need to clay bar your vehicle one time. Multiple passes can ensure you did not miss any areas, however it is not necessary.
After Treatment:
Your paint should be ideally prepped for polishing, glaze, sealant and wax applications. Follow up with the necessary steps depending on the condition of your paint.
Maintenance Schedule:
We suggest clay baring your paint at least twice a year, once during the Spring and once during the Fall. These two details should be more thorough than your normal details and will help maintain your vehicle with ease.
Medium Grade Clay Bar (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to using any type of clay bar. This will help remove major surface contamination and prep the paint for using the clay bar.
Products Recommended:
Clay Magic Medium Grade Bar
Quick Detail Spray
Microfiber Towel
Steps Taken:
1. Cut down the 200 gram into manageable sizes, we suggest using 50 gram pieces or ¼ of your full bar
2. Store remaining ¾ in the protective case along with a few sprays of the quick detailer to keep product moist
3. Kneed the 50 gram piece in your hand eventually working it into a flattened surface
4. Once your piece of clay is ready, directly mist your quick detailer onto the paint to lubricate the surface. Try to work in 2’ x 2’ sections
5. Using light pressure, glide the clay on the surface that you just lubricated. You should feel the dirt and grime being absorbed by the clay
6. When the 2’ x 2’ section is gliding effortlessly, then that area is complete
7. Remove excess quick detailer with a Microfiber Towel
8. As you move onto the next area, keep reshaping the clay in the palm of your hand so you get a fresh surface of clay
9. Repeat steps 3 – 8 until entire vehicle has been clayed
Total Number of Coats Suggested:
You should only need to clay bar your vehicle one time. Multiple passes can ensure you did not miss any areas, however it is not necessary.
After Treatment:
Your paint should be ideally prepped for polishing, glaze, sealant and wax applications. Follow up with the necessary steps depending on the condition of your paint.
Maintenance Schedule:
We suggest clay baring your paint at least twice a year, once during the Spring and once during the Fall. These two details should be more thorough than your normal details and will help maintain your vehicle with ease.
Fine Grade Clay Bar (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to using any type of clay bar. This will help remove major surface contamination and prep the paint for using the clay bar.
Products Recommended:
ClearKote Clay Bar
Quick Detail Spray
Microfiber Towel
Steps Taken:
1. Cut down the 200 gram into manageable sizes, we suggest using 50 gram pieces or ¼ of your full bar
2. Store remaining ¾ in the protective case along with a few sprays of the quick detailer to keep product moist
3. Kneed the 50 gram piece in your hand eventually working it into a flattened surface
4. Once your piece of clay is ready, directly mist your quick detailer onto the paint to lubricate the surface. Try to work in 2’ x 2’ sections
5. Using light pressure, glide the clay on the surface that you just lubricated. You should feel the dirt and grime being absorbed by the clay
6. When the 2’ x 2’ section is gliding effortlessly, then that area is complete
7. Remove excess quick detailer with a Microfiber Towel
8. As you move onto the next area, keep reshaping the clay in the palm of your hand so you get a fresh surface of clay
9. Repeat steps 3 – 8 until entire vehicle has been clayed
Total Number of Coats Suggested:
You should only need to clay bar your vehicle one time. Multiple passes can ensure you did not miss any areas, however it is not necessary.
After Treatment:
Your paint should be ideally prepped for polishing, glaze, sealant and wax applications. Follow up with the necessary steps depending on the condition of your paint.
Maintenance Schedule:
We suggest clay baring your paint at least twice a year, once during the Spring and once during the Fall. These two details should be more thorough than your normal details and will help maintain your vehicle with ease.
Moose Wax Buffer Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying ClearKote Moose Wax. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as these products are not designed to remove them.
Products Recommended with PC 7424:
ClearKote Moose Wax
Porter Cable 7424 with White Polishing Pad or Black Finishing Pad
Microfiber Towel
Dispenser Bottle
Quick Detail Spray
Steps Taken via Porter Cable Application:
1. Pour ClearKote Moose Wax into a smaller dispenser bottle for easier application
2. Mist the applicator pad with quick detailer spray
3. Apply a thin amount around the edge of the pad
4. Create a 2’ x 2’ section that you plan on buffing and spread the product around the surface with the buffer turned off
5. Start the buffer on at a low speed, and work your way up to 4 – 5 as your buffing the product
6. Work the buffer at 3 inches per second pace or slower and pass over each area at least four times
7.Once the area is complete, shut the buffer down and pull the buffer off of the paint
8. Using a clean Microfiber towel, remove product from paint. No wait time is required.
9. Repeat until entire car is polished and protected
Total Number of Coats Suggested:
For ClearKote Moose Wax, only one coat is needed for optimal results due to it being a chemical cleaner. The coats are not stackable, so doing coat after coat does not yield better protection. Some detailers will apply two coats to ensure that 1 coat completely cleaned the surface and the second coat will ensure proper complete coverage.
After Treatment:
For optimal protection, follow up with a pure sealant. This will help enhance the gloss as long as give it longer protection. Another option would be to top with a pure carnauba wax. This will enhance the depth and shine on the paint.
Maintenance Schedule:
We suggest using ClearKote Moose Wax once every 3 - 4 months, pending on weather condition, location, climate, etc.
Moose Wax Hand Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying ClearKote Moose Wax. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as these products are not designed to remove them.
Products Recommended by Hand:
ClearKote Moose Wax
Microfiber Towel
Hand Applicator Kit (White Pad) - or - Microfiber Hand Applicator Pad
Dispenser Bottle
Quick Detail Spray
Steps Taken via Hand Application:
1. Pour ClearKote Moose Wax into a smaller dispenser bottle for easier application
2. Mist applicator pad with quick detailer spray
3. Dispense thin amount of product onto applicator pad
4. Work product into the paint using light to medium hand pressure
5. Work in 2’ x 2’ sections
6. Using a clean Microfiber towel, remove product from paint. No wait time is required.
7. Repeat until entire car is polished and protected
Total Number of Coats Suggested:
For ClearKote Moose Wax, only one coat is needed for optimal results due to it being a chemical cleaner. The coats are not stackable, so doing coat after coat does not yield better protection. Some detailers will apply two coats to ensure that 1 coat completely cleaned the surface and the second coat will ensure proper complete coverage.
After Treatment:
For optimal protection, follow up with a pure sealant. This will help enhance the gloss as long as give it longer protection. Another option would be to top with a pure carnauba wax. This will enhance the depth and shine on the paint.
Maintenance Schedule:
We suggest using ClearKote Moose Wax once every 3 - 4 months, pending on weather condition, location, climate, etc.
Vanilla Moose Buffer Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying ClearKote Vanilla Moose Wax Hand Glaze. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as these products are not designed to remove them.
Products Recommended with PC 7424:
ClearKote Vanilla Moose Wax Hand Glaze
Porter Cable 7424 with White Polishing Pad or Black Finishing Pad
Microfiber Towel
Dispenser Bottle
Quick Detail Spray
Steps Taken via Porter Cable Application:
1. Pour ClearKote VM into a smaller dispenser bottle for easier application
2. Mist the applicator pad with quick detailer spray
3. Apply a thin amount around the edge of the pad
4. Create a 2’ x 2’ section that you plan on buffing and spread the product around the surface with the buffer turned off
5. Start the buffer on at a low speed, and work your way up to 4 – 5 as your buffing the product
6. Work the buffer at 3 inches per second pace or slower and pass over each area at least four times
7.Once the area is complete, shut the buffer down and pull the buffer off of the paint
8. Using a clean Microfiber towel, remove product from paint. No wait time is required.
9. Repeat until entire car is polished.
Total Number of Coats Suggested:
For ClearKote Vanilla Moose Wax Hand Glaze, multiple coats can be used in order to finish the paint further and further. Some detailers will do a coat of VM with a White Polishing Pad then finish it even further with a second coat on a Black Finishing Pad.
After Treatment:
For optimal protection, follow up with a pure sealant. This will help enhance the gloss as long as give it longer protection. Another option would be to top with a pure carnauba wax. This will enhance the depth and shine on the paint.
Maintenance Schedule:
We suggest using ClearKote Vanilla Moose Wax Hand Glaze as desired, but would suggest at least twice a year. Others will use it to remove previous coats of sealant or wax and use it as a pre-wax cleaner and may do it as frequently as every time they plan on waxing the vehicle.
Vanilla Moose Hand Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying ClearKote Moose Wax. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as these products are not designed to remove them.
Products Recommended by Hand:
ClearKote Vanilla Moose Wax Hand Glaze
Microfiber Towel
Hand Applicator Kit (White, Blue or Black Pad)
- or - Microfiber Hand Applicator Pad
Dispenser Bottle
Quick Detail Spray
Steps Taken via Hand Application:
1. Pour ClearKote VM into a smaller dispenser bottle for easier application
2. Mist applicator pad with quick detailer spray
3. Dispense thin amount of product onto applicator pad
4. Work product into the paint using light to medium hand pressure
5. Work in 2’ x 2’ sections
6. Using a clean Microfiber towel, remove product from paint. No wait time is required.
7. Repeat until entire car is polished
Total Number of Coats Suggested:
For ClearKote Vanilla Moose Wax Hand Glaze, multiple coats can be used in order to finish the paint further and further. Use as desired.
After Treatment:
For optimal protection, follow up with a pure sealant. This will help enhance the gloss as long as give it longer protection. Another option would be to top with a pure carnauba wax. This will enhance the depth and shine on the paint.
Maintenance Schedule:
We suggest using ClearKote Vanilla Moose Wax Hand Glaze as desired, but would suggest at least twice a year. Others will use it to remove previous coats of sealant or wax and use it as a pre-wax cleaner and may do it as frequently as every time they plan on waxing the vehicle.
Carnauba Moose Wax Buffer Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying ClearKote Carnauba Moose Wax. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as these products are not designed to remove them.
Products Recommended with PC 7424:
ClearKote Carnauba Moose Wax
Porter Cable 7424 with Black Finishing Pad
Microfiber Towel
Dispenser Bottle
Quick Detail Spray
Steps Taken via Porter Cable Application:
1. Pour ClearKote CMW into a smaller dispenser bottle for easier application
2. Mist Black Finishing pad with quick detailer spray
3. Apply a thin amount around the edge of the Black Finishing pad
4. Create a 2’ x 2’ section that you plan on buffing and spread the product around the surface with the buffer turned off
5. Start the buffer on at a low speed, and work your way up to 3.5 - 4.5 as your buffing the product
6. Work the buffer at 3 inches per second pace or slower and pass over each area at least four times
7. Once the area is complete, shut the buffer down and pull the buffer off of the paint
8. No wait time before removal, using a clean Microfiber towel, remove product from paint
9. Repeat until entire car is protected
Total Number of Coats Suggested:
For ClearKote CMW, coats are stackable, so one may wish to layer this product 3 coats for additional gloss and depth, maxium 5 coats.
Maintenance Schedule:
We suggest using ClearKote CMW once every 2 - 8 weeks, pending on weather condition, location, climate, etc. In between applications we suggest using ClearKote Quick Shine after regular washes to enhance depth and gloss, add surface slickness and added protection.
Carnauba Moose Wax Hand Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying ClearKote CMW. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as these products are not designed to remove them.
Products Recommended by Hand:
ClearKote Carnauba Moose Wax
Microfiber Towel
Hand Applicator Kit (Blue or Black Pad) - or - Microfiber Hand Applicator Pad
Dispenser Bottle
Quick Detail Spray
Steps Taken via Hand Application:
1. Pour ClearKote CMW into a smaller dispenser bottle for easier application
2. Mist applicator pad with quick detailer spray
3. Dispense thin amount of product onto applicator pad
4. Work product into the paint using light hand pressure
5. Work in 2’ x 2’ sections
6. No wait time before removal, using a clean Microfiber towel, remove product from paint
7. Repeat until entire car is protected
Total Number of Coats Suggested:
For ClearKote CMW, coats are stackable, so one may wish to layer this product 3 coats for additional gloss and depth, maxium 5 coats.
Maintenance Schedule:
We suggest using ClearKote CMW once every 2 - 8 weeks, pending on weather condition, location, climate, etc. In between applications we suggest using ClearKote Quick Shine after regular washes to enhance depth and gloss, add surface slickness and added protection.
Metal Polish (Return to Product List)
Prior to Use:
Ensure the surface is cool to the touch. Work in a shaded area.
Products Recommended:
ClearKote Metal Polish
2 Sided Polishing Towel
Steps Taken:
1. Dispense a small amount of product onto the microfiber towel (grittier side)
2. Lightly massage the product onto the metal surface using light pressure
3. Work the product into the paint until a haze forms
4. Flip the microfiber towel over (softer side) and wipe down the haze
5. Repeat to enhance gloss and depth
After Cleaning:
To protect and reduce more brake dust build up we suggest using a Wheel Protectant after using ClearKote Metal Polish.
Maintenance Schedule:
We suggest cleaning your metal as frequently as you desire. We recommend at a minimum monthly cleanings. Cleaning more frequently allows you to remove contamination while its fresh.
Quick Shine (Return to Product List)
ClearKote Quick Shine – Pad Lubrication for your Porter Cable:
Misting you pads prior to buffing will help provide lubrication and more effectiveness out of your polish. It will help keep the polish on the surface of the pad and also help spread it more effectively. When using a new pad, mist slightly more product than normal use. Mist as needed, however we suggest at least reapplying quick detailer onto the pad at least three times during a coat.After the coat is finished, make sure you clean the pad thoroughly with Snappy Clean Pad Cleaners.
ClearKote Quick Shine – Clay Bar Lubricant:
When using a clay bar, you want to make sure the surface you are trying to remove contamination on is properly lubricated, otherwise, you will notice the clay bar skid, stick, or smudge the paint. With out proper lubrication you can severely reduce the benefits of using a clay bar. Each spot of your 2’ x 2’ area should have some quick detailer on it. If you feel the clay getting stuck to your paint or it is skipping across, you know you do not have enough lubrication. Wipe off excess Quick Shine with a microfiber towel.
ClearKote Quick Shine – Post Wash and Touch Ups:
It is very difficult to achieve a perfect wash and dry. There may be some small water droplets that you forgot to remove, contaminates, etc. You can use the Quick Shine as a quick detailer right after you wash and dry your vehicle to ensure you have fully cleaned the vehicle. Another major benefit from quick detailing is that it will enhance the gloss and depth. Mist a clean Microfiber towel with the Quick Shine and begin to gently go over the freshly washed surface. After a couple of panels, flip the towel over to an unused portion and repeat the process until the entire car has been quick detailed. Another method is to mist the paint with quick detailer while it is still wet and dry the car as normal. It is like killing two birds with one stone, drying and quick detailing in 1 step.
Tire Dressing (Return to Product List)
Prior to Treatment:
If tire is stained, dirty or discolored, clean the area with the proper cleaner to prep the surface for protection. We suggest Poorboy's APC Biodegradable Cleaner to prep the surface prior to applying tire dressing.
Products Recommended:
ClearKote Tire Dressing
Tire Dressing Applicator
Steps Taken:
1. Mist ClearKote Tire Dressing onto an applicator pad
2. Spread the product onto the tire by wiping the applicator pad around the tire
3. Repeat steps 1 & 2 until entire surface has been covered with Bold 'n Bright
For a matte finish, use a separate Microfiber towel and buff completely dry
For a semi-gloss, do not buff dry
Maintenance Schedule:
We suggest applying after washes, or every 1 - 3 weeks to maintain the desired finish.
Red Moose Glaze Buffer Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying ClearKote Red Moose Glaze. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as this products is not designed to remove them.
Products Recommended with PC 7424:
ClearKote Red Moose Glaze
Porter Cable 7424 with White Polishing Pad or Black Finishing Pad
Microfiber Towel
Dispenser Bottle
Quick Detail Spray
Steps Taken via Porter Cable Application:
1. Pour RMG into a smaller dispenser bottle for easier application
2. Apply a thin amount around the edge of the pad
3. Create a 2’ x 2’ section that you plan on buffing and spread the product around the surface with the buffer turned off
4. Start the buffer on at a low speed, and work your way up to 3.5 - 5 as your buffing the product
5. Work the buffer at 3 inches per second pace or slower and pass over each area at least four times
6. Once the area is complete, shut the buffer down and pull the buffer off of the paint
7. No wait time before removal, using a clean Microfiber towel, remove product from paint
8. Repeat until entire car is glazed
Total Number of Coats Suggested:
For RMG, multiple coats can be applied to add additional gloss and depth to the paint, however the benefits diminish each coat as less imperfections will be filled in.
After Treatment:
For optimal protection, follow up with a pure sealant. This will help enhance the gloss as long as give it longer protection. Another option would be to top with a pure carnauba wax. This will enhance the depth and shine on the paint.
Maintenance Schedule:
We suggest using ClearKote RMG once every 3 – 4 months, pending on weather condition, location, climate, etc. This should be done the same time you reapply your sealant for protection.
Red Moose Glaze Hand Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying ClearKote Red Moose Glaze. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as these products are not designed to remove them.
Products Recommended by Hand:
ClearKote Red Moose Glaze
Microfiber Towel
Hand Applicator Kit (White or Blue Pad) - or - Microfiber Hand Applicator Pad
Dispenser Bottle
Quick Detail Spray
Steps Taken via Hand Application:
1. Pour RMG into a smaller dispenser bottle for easier application
2. Mist applicator pad with quick detailer spray
3. Dispense thin amount of product onto applicator pad
4. Work product into the paint using light hand pressure
5. Work in 2’ x 2’ sections
6. No wait time before removal, using a clean Microfiber towel, remove product from paint
7. Repeat until entire car is glazed
Total Number of Coats Suggested:
For RMG, multiple coats can be applied to add additional gloss and depth to the paint, however the benefits diminish each coat as less imperfections will be filled in.
After Treatment:
For optimal protection, follow up with a pure sealant. This will help enhance the gloss as long as give it longer protection. Another option would be to top with a pure carnauba wax. This will enhance the depth and shine on the paint.
Maintenance Schedule:
We suggest using ClearKote RMG once every 3 – 4 months, pending on weather condition, location, climate, etc. This should be done the same time you reapply your sealant for protection.
Glass Scrub (Return to Product List)
Prior to Use:
Before using the glass scrub, wash the windshield normally with soap and water to get major contamination off of the surface such as bugs, bird droppings, etc. This step should be done after washing but prior to drying off the car since you will need to hose off excess product.
Products Recommended:
Glass Scrub
Foam Applicator Pad
Microfiber Waffle Weave Drying Towel
Steps Taken:
1. Flood the surface prior to applying the glass scrub
2. Put a dime to nickel sized drop of product on the Foam Applicator Pad
3. Work the product into the surface using light to medium pressure while the glass is still wet, it should begin to turn into a creamy foam on your glass
4. Continue this process until all of the glass is cleaned with the Glass Scrub
5. Rinse off excess product with a hose, you should notice the water sheeting right off
6. Dry the surface as normal
After Treatment:
We suggest following up the Glass Scrub with Glass Science Rain Clear. The Glass Scrub properly preps the surface for adding the latest technology for rain repellant Rain Clear.
Maintenance Schedule:
Use Glass Science Glass Scrub as needed.
Rain Clear (Return to Product List)
Prior to Use:
We strongly suggest using the Glass Science Glass Scrub prior to using the Glass Science Rain Clear. This will help prep the glass to accept the Rain Clear treatment.
Products Recommended:
Glass Science Rain Clear
Microfiber Towel
Steps Taken:
1. Put about a nickel to quarter sized drop on a corner of a microfiber towel
2. Work the product into the glass using light to medium pressure
3. Flip the microfiber towel over to a clean side and buff off any haze, the glass should not have any haze after this step
4. Repeat until all of the glass you want to protect is done
Maintenance Schedule:
Clean your glass as needed with Stoner’s Invisible Glass. Reapply Rain Clear after water begins to stop sheeting off the glass.
Fog Clear (Return to Product List)
Prior to Use:
Clean your glass with Stoner's Invisible Glass.
Products Recommended:
Glass Science Fog Clear
Microfiber Towel
Steps Taken:
1. Put about a nickel to quarter sized drop on a corner of a microfiber towel
2. Work the product into the glass using light to medium pressure
3. Flip the microfiber towel over to a clean side and buff off any haze, the glass should not have any haze after this step
4. Repeat until all of the glass you want to protect is done
Maintenance Schedule:
Reapply Fog Clear as needed.
All In One Buffer Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying Klasse All In One. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as these products are not designed to remove them.
Products Recommended with PC 7424:
Klasse All In One
Porter Cable 7424 with White Polishing Pad
Microfiber Towel
Dispenser Bottle
Quick Detail Spray
Steps Taken via Porter Cable Application:
1. Pour Klasse AIO into a smaller dispenser bottle for easier application
2. Mist White Polishing pad with quick detailer spray
3. Apply a thin amount around the edge of the White Polishing pad
4. Create a 2’ x 2’ section that you plan on buffing and spread the product around the surface with the buffer turned off
5. Start the buffer on at a low speed, and work your way up to 4.5 – 6 as your buffing the product
6. Work the buffer at 3 inches per second pace or slower and pass over each area at least four times
7. Once the area is complete, shut the buffer down and pull the buffer off of the paint
8. No wait time before removal, using a clean Microfiber towel, remove product from paint
9. Repeat until entire car is polished and protected
Total Number of Coats Suggested:
For Klasse All In One, only one coat is needed for optimal results due to it being a chemical cleaner. The coats are not stackable, so doing coat after coat does not yield better protection. Some detailers will apply two coats to ensure that 1 coat completely cleaned the surface and the second coat will ensure proper complete coverage.
After Treatment:
For optimal protection, follow up with a pure sealant. This will help enhance the gloss as long as give it longer protection. Another option would be to top with a pure carnauba wax. This will enhance the depth and shine on the paint.
Maintenance Schedule:
We suggest using Klasse All In One once every 3 – 4 months, pending on weather condition, location, climate, etc. In between applications we suggest using Menzerna High Gloss Acrylic Shield after regular washes to enhance depth and gloss, add surface slickness and added protection.
All In One Buffer Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying Klasse All In One. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as these products are not designed to remove them.
Products Recommended by Hand:
Klasse All In One
Microfiber Towel
Hand Applicator Kit (White or Blue Pad) - or - Microfiber Hand Applicator Pad
Dispenser Bottle
Quick Detail Spray
Steps Taken via Hand Application:
1. Pour Klasse AIO into a smaller dispenser bottle for easier application
2. Mist applicator pad with quick detailer spray
3. Dispense thin amount of product onto applicator pad
4. Work product into the paint using light to medium hand pressure
5. Work in 2’ x 2’ sections
6. No wait time before removal, using a clean Microfiber towel, remove product from paint
7. Repeat until entire car is polished and protected
Total Number of Coats Suggested:
For Klasse All In One, only one coat is needed for optimal results due to it being a chemical cleaner. The coats are not stackable, so doing coat after coat does not yield better protection. Some detailers will apply two coats to ensure that 1 coat completely cleaned the surface and the second coat will ensure proper complete coverage.
After Treatment:
For optimal protection, follow up with a pure sealant. This will help enhance the gloss as long as give it longer protection. Another option would be to top with a pure carnauba wax. This will enhance the depth and shine on the paint.
Maintenance Schedule:
We suggest using Klasse All In One once every 3 – 4 months, pending on weather condition, location, climate, etc. In between applications we suggest using Menzerna High Gloss Acrylic Shield after regular washes to enhance depth and gloss, add surface slickness and added protection.
High Gloss Sealant Glaze Buffer Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying Klasse High Gloss Sealant Glaze. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as this product is not designed to remove them.
Products Recommended with PC 7424:
Klasse High Gloss Sealant Glaze
Porter Cable 7424 with Black Finishing Pad
Microfiber Towel
Dispenser Bottle
Quick Detail Spray
Steps Taken via Porter Cable Application:
1. Pour Klasse HGSG into a smaller dispenser bottle for easier application
2. Mist the pad with quick detailer spray
3. Apply a thin amount around the edge of the pad
4. Create a 2’ x 2’ section that you plan on buffing and spread the product around the surface with the buffer turned off
5. Start the buffer on at a low speed, and work your way up to 3.5 – 4.5 as your buffing the product
6. Work the buffer at 3 inches per second pace or slower and pass over each area at least four times
7.Once the area is complete, shut the buffer down and pull the buffer off of the paint
8. Repeat until entire car is protected
9. Using a clean Microfiber towel, remove product from paint or let the product sit on the paint up to 24 hours for easier removal.
Total Number of Coats Suggested:
Klasse High Gloss Sealant Glaze can be layered to achieve additional depth and gloss as well as more durable protection. Klasse suggests a 5 coat maximum for optimal results.
After Treatment:
For optimal depth and gloss, follow up with a pure carnauba wax.
Maintenance Schedule:
We suggest using Klasse High Gloss Sealant Glaze once every 4 - 6 months, pending on weather condition, location, climate, etc. In between applications we suggest using Menzerna High Gloss Acrylic Shield after regular washes to enhance depth and gloss, add surface slickness and added protection.
High Gloss Sealant Glaze Hand Application (Return to Product List)
Prior to Use:
Washing and drying your vehicle is a must prior to applying Klasse High Gloss Sealant Glaze. For optimal results we also suggest using a clay bar to prep the vehicles paint for easier application and longer lasting results. Also, be sure to have your swirls and scratches removed with polish(es) as these products are not designed to remove them.
Products Recommended by Hand:
Klasse High Gloss Sealant Glaze
Microfiber Towel
Hand Applicator Kit (Black Pad) - or - Microfiber Hand Applicator Pad
Dispenser Bottle
Quick Detail Spray
Steps Taken via Hand Application:
1. Pour Klasse HGSG into a smaller dispenser bottle for easier application
2. Mist applicator pad with quick detailer spray
3. Dispense thin amount of product onto applicator pad
4. Work product into the paint using lig | 