|
|
|
Lamin-X
Headlight kit
Tired of having to worry all the time about your Touareg
headlights being scratched, rock chipped, or even cracked?
Lamin-X Pre-cut kits are
the solution to all your exterior lighting needs; Thick, Strong,
Flexible, and Invisible, Lamin-x provides clear and colored protective
films that protect highly impacted easily damages areas. Use on
headlights, taillights, foglights, or many other surfaces. Preserve the
value and appearance of your vehicle.
Colors Available:
Clear (20 / 40mm), Yellow, Blue, or Smoked.

What is the difference between 20mm
and 40mm clear film? 20 mm -
Strong, perfectly invisible protection for lights and lenses. Keep your
lights looking new for years and years.No more yellow, hazy lights from
sand blasting and rocks chips. Very flexible and pliable for very
rounded/curved light applications. Adhesive backed for easy and very
forgiving application to any surface. Great heat dissipation properties
for those high heat/intensity lighting. Handles up to 300-degree temps.
40 mm - Lamin-X's thickest and strongest film yet. 1/16th thick!
Perfectly clear, invisible protection for lights and lenses. Keep your
lights looking new for years and years. No more yellow, hazy lights from
sand blasting and rocks chips. Adhesive backed for easy and very
forgiving application to any surface. Excellent protection for flat and
lower temperature lenses. Handles up to 300-degree temps.
Physical
Properties and Test Results |
- Complies
with WAC 296-62-054 and 29 CFR 1910.1200.
- Product
is impact resistant, softened PCV vinyl film.
-
Cushioning effect reduces or eliminates projectile damage.
- Easily
shaped and curved with heat.
-
Installations errors can be corrected while being installed.
-
Breathable for quicker curing.
- Product
is scratch resistant, but any created cracks or scratches
will disappear with time.
- Resists
yellowing with minor yearly maintenance (any UV protectant
conditioner or screen - like Meguiars, Turtle Wax, Mothers,
303 Protectants).
Product storage info:
Do not store near heat or direct/indirect sunlight. Average
shelf life of one year when stored in original packaging. Do not
store in an unwound condition (will cause film to pull up from
backing material over time). |
**Note: Testing information is, to the best of the company's knowledge,
accurate under numerous conditions; however, it does not apply in all
cases. The summary chart is intended as a guideline and all
recommendations are made without guarantee since conditions of use are
beyond our control.
|

Lamin-X Headlight Kit Shown in
Blue on VW Passat |

Lamin-X Headlight Kit Show in
Yellow on BMW E36 |

Lamin-X Headlight Kit Shown in
Smoked on BMW E46 M3 |
Lamin-X
Fog Light kit
Tired of having to worry all the time about your Touareg fog
lights being scratched, rock chipped, or even cracked?
Lamin-X Pre-cut kits are
the solution to all your exterior lighting needs; Thick, Strong,
Flexible, and Invisible, Lamin-x provides clear and colored protective
films that protect highly impacted easily damages areas. Use on
headlights, taillights, foglights, or many other surfaces. Preserve the
value and appearance of your vehicle.
Colors Available:
Clear (20 / 40mm), Yellow, Blue, or Smoked.

What is the difference between 20mm
and 40mm clear film? 20 mm -
Strong, perfectly invisible protection for lights and lenses. Keep your
lights looking new for years and years.No more yellow, hazy lights from
sand blasting and rocks chips. Very flexible and pliable for very
rounded/curved light applications. Adhesive backed for easy and very
forgiving application to any surface. Great heat dissipation properties
for those high heat/intensity lighting. Handles up to 300-degree temps.
40 mm - Lamin-X's thickest and strongest film yet. 1/16th thick!
Perfectly clear, invisible protection for lights and lenses. Keep your
lights looking new for years and years. No more yellow, hazy lights from
sand blasting and rocks chips. Adhesive backed for easy and very
forgiving application to any surface. Excellent protection for flat and
lower temperature lenses. Handles up to 300-degree temps.
Physical
Properties and Test Results |
- Complies
with WAC 296-62-054 and 29 CFR 1910.1200.
- Product
is impact resistant, softened PCV vinyl film.
-
Cushioning effect reduces or eliminates projectile damage.
- Easily
shaped and curved with heat.
-
Installations errors can be corrected while being installed.
-
Breathable for quicker curing.
- Product
is scratch resistant, but any created cracks or scratches
will disappear with time.
- Resists
yellowing with minor yearly maintenance (any UV protectant
conditioner or screen - like Meguiars, Turtle Wax, Mothers,
303 Protectants).
Product storage info:
Do not store near heat or direct/indirect sunlight. Average
shelf life of one year when stored in original packaging. Do not
store in an unwound condition (will cause film to pull up from
backing material over time). |
**Note: Testing information is, to the best of the company's knowledge,
accurate under numerous conditions; however, it does not apply in all
cases. The summary chart is intended as a guideline and all
recommendations are made without guarantee since conditions of use are
beyond our control.
|

Lamin-X Fog Light Kit Shown in
Yellow on Saab |

Lamin-X Fog Light Kit Shown in
Blue on E46 M3 |
Lamin-x
Small Light Installation
Intall:
Small sized applications may be applied dry and medium to large
light installations may be applied wet for best results.
First, Clean lens
thoroughly. Then peel backing off of film (prevent the film from
touching any foreign surfaces). Wet application: spray a very light mist
of water onto lens (one or two sweeping sprays from 10-12 inchs away is
sufficient). Then align and apply film to one side or center of the
light or area. Then using a plastic application card, press down/sweep
the remainder of the film across the light. If large bubbles are present
or film is misaligned, peel up the film to that area and apply again. If
film is not precut then use an X-acto knife, triangular pointed knife,
or razor blade to trim off the excess film. If product is precut then
remove the handling tabs.
Settling:
Small air bubbles and creases/ripples will disappear over time film
settles and is warmed. Minor scratches will also disappear over time and
after film maintenance by waxing or applying
303 vinyl
conditioner.
Paint and Large Light
Installation Instructions
Our paint protections include complete installation instructions, which
describes the best installation method for each area/piece. Also
included are labeled diagrams of kit. We are also available to verbally
assist the customer if any questions or complications arise. If you do
decide not to install yourself, we can attempt to locate professional
installer within your general vincinity. |
Lamin-x Convex Light Installation
Items needed for large size installations (Small size installs can be
applied dry) :
- Spray bottle filled with 24 oz. of clean water and approx.
Note: a few drops of
methyl hydrate only may be used in the solution to assist in
evaporation
-
One plastic application card, squeegee (body filler card)
- An X-acto knife, breakaway blade, or a razor blade
*DO NOT INSTALL
OR CLEAN WITH ALCOHOL BASED PRODUCTS (Methyl Hydrate acceptable)*
Preparation:
Make sure the area where the film is to be applied is clean and free
from dust, dirt, grease or any other contaminates.
(Use mineral spirits and/or clean soapy water to clean the surface
thoroughly.) Best results are achieved between 60 and 85 degrees F. Wash
hands thoroughly and keep saturated/wet with the application solution to
prevent permanent fingerprints in the adhesive and prevent the film from
properly adhering. Also make sure the film does not come in contact with
the ground or any surface from which it may collect dirt or dust.
Applying:
Kit should be applied dry onto fog lights and headlights. For large
lights, spray a very light mist of the water solution onto lens &
liberally spray on outside of film (non-adhesive). Then align and apply
film to one side or center of the light or area using the handling tabs
. Then using a plastic application card, apply down/squeegee the very
center of the film. Then apply the remainder of the film by moving
in a spiral or circular motion working outwards towards the edge of the
light. The key to positive results is distributing the film evenly
so that wrinkles either do not occur or are manageable. Film is very
forgiving, which allows you to pull and reapply numerous times if not
satisfied with results. This can only be done upon initial
installation, before the curing process. Note: warming the film with a
heat gun or blow dryer can help to mold the film around any difficult,
curved areas.
Once applied: If film is not precut then use an X-acto knife, triangular
pointed knife, or razor blade to score the outside layer of the film
then trim off the excess. If product is precut then remove the handling
tabs. Let film dry for a minimum of 30 minutes and carefully wipe off
any excess solution. If all moisture has not been evacuated under film
then some fogginess of the film will occur. This is completely normal.
Film is breathable and porous – cloudiness/fog will evaporate with a few
days to a few weeks. Depending on film thickness and sunlight/heat
exposure. Any surface texture, scratches, or ripples will also
disappear during this curing process.
*ALLOW 48-72 HOURS FOR ADHESIVE TO SET AND BOND TO YOUR VEHICLE. DO
NOT WASH, NOR DISTURB DURING THE CURING PROCESS.*
Maintenance and Care
The film
can be washed with soap and water just as you use on your car's finish.
Light scrubbing is ok as well as a mild solvent if needed. It is
important to wax the film at least 3 times a year w/ a good carnauba wax
or 303-Products vinyl conditioner to maintain the film's U.V.
protection. |
Lamin-x Large Light Installation
Items needed for large size installations (Small size installs can be
applied dry) :
- Spray bottle filled with 24 oz. of clean water and approx.
Note: a few drops of
methyl hydrate only may be used in the solution to assist in
evaporation
-
One plastic application card, squeegee (body filler card)
- An X-acto knife, breakaway
blade, or a razor blade
*DO
NOT INSTALL OR CLEAN WITH ALCOHOL BASED PRODUCTS (Methyl Hydrate
acceptable)*
Preparation:
Make sure the area where the film is to be applied is clean and free
from dust, dirt, grease or any other contaminates.
(Use mineral spirits and/or clean soapy water to clean the surface
thoroughly.) Best results are achieved between 60 and 85 degrees F. Wash
hands thoroughly and keep saturated/wet with the application solution to
prevent permanent fingerprints in the adhesive and prevent the film from
properly adhering. Also make sure the film does not come in contact with
the ground or any surface from which it may collect dirt or dust.
Applying:
Film can be applied dry onto fog lights and
smaller headlights. For
large lights, spray a very light amount of the water solution onto lens
& liberally spray on outside of film (non-adhesive). Then align and
apply film to one side or center of the light or area using the handling
tabs . Then using a plastic application card, press down/squeegee the
film with smooth sweeping motions. Do this across the remainder of the
light. If large bubbles are present, peel up the film to that area and
apply again. Film is very forgiving, which allows you to pull and
reapply numerous times if not satisfied with results. This can only be
done upon initial installation, before curing process. Note: warming
the film with a heat gun or blow dryer will soften it to help to mold
the film around any difficult, curved areas.
Once applied: If film is not precut then use an X-acto knife, triangular
pointed knife, or razor blade to score the outside layer of the film
then trim off the excess. No need to cut all the way through the film.
If product is precut then remove the handling tabs. Let film dry for a
minimum of 30 minutes and carefully wipe off any excess solution. If
all moisture has not been evacuated under film then some fogginess of
the film will occur. This is completely normal. Film is breathable and
porous – cloudiness/fog will evaporate with a few days to a few weeks.
Depending on film thickness and sunlight/heat exposure. Any surface
texture, scratches, or ripples will also disappear during this curing
process.
*ALLOW 48-72 HOURS FOR ADHESIVE TO SET AND BOND TO YOUR VEHICLE. DO
NOT WASH, NOR DISTURB DURING THE CURING PROCESS.*
Maintenance
and Care
The film
can be washed with soap and water just as you use on your car's finish.
Light scrubbing is ok as well as a mild solvent if needed. It is
important to wax the film at least 3 times a year w/ a good carnauba wax
or 303-Products vinyl conditioner to maintain the film's U.V.
protection. |
Q - Can the film be removed without
damage?
A.
Lamin-x film can be easily removed without damage to the light or
original paint. Upon initial application, the film can be pulled back up
and reapplied numerous times if not installed correctly. The film and
adhesive is forgiving enough for this. Once the film is settled (appx
48-72 hours) the product is not considered to be reusable. Upon removal
warm the film and lift off slowly.
Q - Are your colored films legal on
headlights for street use?
A.
Our colored films may not be legal for street use on primary lighting.
An off-road disclosure is recommended. Please check your state or local
laws before application. Installation of colored Lamin-x Films on your
primary lights is done so at your own peril. None of our films produce a
blue or red light when lit.
Q
- I just installed the film on my
lights. There are still some tiny bubbles and milkiness underneath and
creases/ripples on top of the film. What should I do?
A.
Once the film settles any small bubbles/milkiness or application creases
will disappear. Lamin-x is a breathable PVC vinyl film. Tiny air pockets
will evaporate. The creases/ripples caused by application cards or your
finger will smooth out once settled and warmed.
Q - What's the difference between your
film and your competitors?
A.
Numerous things make our product more appealing than others, such as:
- Our films are impact resistant and a softened PVC vinyl film. Most
competitor films are not impact resistant and have a top-coated urethane
film.
- Installation errors can be corrected and repaired upon installation.
- Lamin-x is breathable for quicker curing and allows for newly applied
paint to fully cure.
- Resists yellowing with minor yearly maintenance.
- Multiple colors and thicknesses available for multiple uses.
- Competitors only have clear films. No colors available.
Q - What is the 5-year guarantee?
A.
Lamin-x Protective Films guarantees its products for five years from the
date of purchase. The products are guaranteed against defective
materials and workmanship, This guarantee is null and void if the
products have been improperly handled or applied. Neither the seller nor
the manufacturer shall be liable for any injury, loss or damage, direct
or consequential, arising out of the use or inability to use the
products. If the products are not proven to conform to specifications
the seller's and manufacturer's obligations shall be to replace it at no
cost to the purchaser. All expressed or implied rights, warranties,
guarantees, or conditions, stutory or otherwise, are excluded. The
foregoing may not be altered, except by agreement signed by the buyer
and seller, and is void where prohibited by law. During the three year
guarantee period, you Lamin-x Protective Films product will be replaced
free of charge, when proof of purchase and the defective product are
returned to the seller or the manufacturer.
|
|
|
|