The Diode Dynamics LED Interior upgrade Kit for
2015+ Ford Mustang
This interior LED conversion kit in the color of your choice includes:
Stage 1 Kit:
2-194 HP3 Map Light LED Bulbs
1-194 HP3 Trunk Light LED Bulb
1-194 HP3 Glove Light LED Bulb
4-74 SMD1 Vanity Light LED Bulbs
Stage 2 Kit:
2-194 HP5 Map Light LED Bulbs
1-194 HP5 Trunk Light LED Bulb
1-194 HP5 Glove Light LED Bulb
4-74 SMD1 Vanity Light LED Bulbs
Diode Dynamics LED Conversion Kits include all of the LED bulbs you need
to replace the incandescent bulbs in your vehicle. It has been tested in
your specific vehicle, for perfect fitment, and no guesswork! No
modification is required for installation, you simply replace the
design, with one 5050-size Epistar SMD chip. Outputs at 180 degrees.
compact design, with two 5050-size Epistar SMD chips, driven at high
power for maximum effective brightness. Outputs at 180 degrees.
high-power SMD under a diffusing lens for truly even output (no
hotspots). Constant current design and air-cooled base for superior
reliability. Features dual contact pins and nonpolar function for easy
high-power SMDs, under a diffusing lens. Just like the HP3, but run at
higher power, with integrated copper plating for superior heat
dissipation, allowing maximum brightness.
bulbs use a quality inject-molded 194/168 T10 terminal, with a full-size
base connector and proper pin alignment, designed for exact replacement
of your factory 194 bulb. Just remove the old bulb, and plug in the new
your order is ONE BULB.
Bulb appearance may vary depending on which LED reverse bulb you choose.
BEWARE! Most sellers just provide "calculated" lumen numbers, based on
the maximum potential brightness of the LED chips on the bulb. For
example, if a bulb has five 10-lumen chips, they will rate it at 50
lumens. However, this is not accurate, as the design of an LED bulb does
not get rid of heat fast enough to run the LEDs at maximum.
These "calculated" lumen ratings are much, much higher than the true,
measured light output, so it will look like competitors' bulbs are
brighter than ours. This is because Diode Dynamics does not provide
inflated "calculated" numbers; we believe it is misleading. We test the
actual brightness of the bulbs in our lab, to provide real lumen output
measurements. Our measurements are accurate, but they are usually much
lower than the misleading "calculated" figures. Please click
here to learn more about LED brightness measurement.
This LED package will provide a substantial improvement in brightness
compared to stock. The factory bulbs are 35 lumens each, while the
replacement Cool White Stage 1 HP3 Bulbs are 55 lumens and the Cool
White Stage 2 HP5 Bulbs are 92 lumens each.
Lumens: BUYER BEWARE! Most sellers just provide "calculated" lumen
numbers, based on the maximum potential brightness of the LED chips on
the bulb. For example, if a bulb has five 10-lumen chips, they will rate
it at 50 lumens. However, this is not accurate, as the design of an LED
bulb does not get rid of heat fast enough to run the LEDs at maximum.
Components. Diode Dynamics uses only the highest quality LED
chips in the production of its bulbs. This means we use only brand-name
suppliers such as Epistar, Cree, Osram, and Samsung.
While our bulbs may look the same as others on the market, most copycat
bulbs use economy-grade LED chips in order to reduce costs. This greatly
reduces the reliability and overall brightness of the bulb when you
compare it to Diode Dynamics.
Construction. Although LED technology allows for extremely long
bulb life, the market is flooded with cheap LED bulbs that fail
prematurely due to inferior construction. The worst enemy of LEDs is
excessive heat, and when bulbs are not designed properly, they do not
disperse heat as well, leading to premature failure.
Off-brand, cheap bulbs exhibit poor solder uniformity, high levels of
flux in the solder, uneven chip placement, low-gauge terminal wires,
poor assembly, and bulbs held together with inferior adhesives. At best,
solder joints will crack and fail on low-quality LEDs after a few weeks
of use. In the worst case, these bulbs can damage housings as the extra
flux and adhesive evaporates and creates a residue on the lens of the
Diode Dynamics bulbs are produced with modern, computerized equipment,
and only the best materials, to ensure complete uniformity, high
quality, and long bulb life.